OmniConverter GXPoE+/S and GXHPoE/S are unmanaged gigabit PoE Extenders that enable the delivery of Ethernet data and Power over Ethernet (PoE) beyond the standard 100 meter limit of twisted pair copper cabling. OmniConverter PoE Extenders provide cost-effective distance extension and connectivity to remote PoE devices where external power is not available or hard to provision, or when replacing copper with fiber becomes cost prohibitive. OmniConverter PoE Extenders are 10/100/1000BASE-T Ethernet extenders that function as both Powered Devices (PD) and Power Sourcing Equipment (PSE), and require no external AC power. They feature one PoE/PD port and one or two PoE/PSE ports, and can be powered by an IEEE 802.3at or High-Power PoE 60W power source, such as an OmniConverter GHPoE/Sx or GHPoE/M HPoE PSE switch. Utilizing data regeneration and voltage level boosting capabilities, OmniConverter PoE Extenders can be daisy chained to break through the Ethernet copper distance barrier and deliver 10/100/1000 data and power to multiple PoE powered devices. Due to cable resistance, voltage drop across the cabling could lower the voltage below the minimum standard requirement of the attached PD. OmniConverter PoE Extenders have smart voltage-boosting technology to maintain the required standard compliant PoE voltage levels between hops. The PoE Extenders automatically negotiate and deliver the power level required by a Powered Device (PD) partner. When a non-PoE device, such as a laptop, is connected to the PoE Extenders for data only applications, no power is applied. OmniConverter PoE Extenders are plug-and-play devices that support auto-negotiation of data rates and duplex modes for simple in-line installation to instantly extend network distances. The PoE Extenders are fully operational once a PSE source is applied to the PoE/PD port, displaying power and operational status without a PD attached. This facilitates the installation and troubleshooting by ensuring each link is operational. The OmniConverter PoE Extenders can be wall mounted or DIN-rail mounted using the optional DIN-rail mounting clip.

OmniConverter GXPoE+/S and GXHPoE/S are unmanaged gigabit PoE Extenders that enable the delivery of Ethernet data and Power over Ethernet (PoE) beyond the standard 100 meter limit of twisted pair copper cabling. OmniConverter PoE Extenders provide cost-effective distance extension and connectivity to remote PoE devices where external power is not available or hard to provision, or when replacing copper with fiber becomes cost prohibitive. OmniConverter PoE Extenders are 10/100/1000BASE-T Ethernet extenders that function as both Powered Devices (PD) and Power Sourcing Equipment (PSE), and require no external AC power. They feature one PoE/PD port and one or two PoE/PSE ports, and can be powered by an IEEE 802.3at or High-Power PoE 60W power source, such as an OmniConverter GHPoE/Sx or GHPoE/M HPoE PSE switch. Utilizing data regeneration and voltage level boosting capabilities, OmniConverter PoE Extenders can be daisy chained to break through the Ethernet copper distance barrier and deliver 10/100/1000 data and power to multiple PoE powered devices. Due to cable resistance, voltage drop across the cabling could lower the voltage below the minimum standard requirement of the attached PD. OmniConverter PoE Extenders have smart voltage-boosting technology to maintain the required standard compliant PoE voltage levels between hops. The PoE Extenders automatically negotiate and deliver the power level required by a Powered Device (PD) partner. When a non-PoE device, such as a laptop, is connected to the PoE Extenders for data only applications, no power is applied. OmniConverter PoE Extenders are plug-and-play devices that support auto-negotiation of data rates and duplex modes for simple in-line installation to instantly extend network distances. The PoE Extenders are fully operational once a PSE source is applied to the PoE/PD port, displaying power and operational status without a PD attached. This facilitates the installation and troubleshooting by ensuring each link is operational. The OmniConverter PoE Extenders can be wall mounted or DIN-rail mounted using the optional DIN-rail mounting clip.

The iConverter T1/E1 media converter provides standard T1 (1.544Mbps) or E1 (2.048Mbps) copper-to-fiber conversion and can be used to extend the demarcation point between service provider and networking equipment. T1/E1 media converters operate in pairs, extending distances over fiber, which improves noise immunity, quality of service, intrusion protection and network security.Designed as a transparent repeater, the iConverter T1/E1 supports standard T1, E1 and Primary Rate Interface (PRI), voice or data. The converter also supports AMI, B8ZS and HDB3 line codes. DIP-switches provide easy configuration of T1/E1 line codes and line build-out.The iConverter T1/E1 is available as a compact, unmanaged standalone unit with an RJ48 interface or as a chassis managed plug-in module with RJ48 or coax interface.

The FlexPoint Powered Chassis is a 19" rack-mount chassis that houses up to 14 standalone FlexPoint media converter modules. The redundant power supplies are essential where reliability is important, and in mission-critical applications to ensure continuous operation.Both of the universal AC or DC power supplies are hot-swappable and can be used in any combination. In case of a failure, a power supply can be hot-replaced while the second power supply supports the operation of the chassis.The power control logic of the Powered Chassis provides loadsharing between the power supplies, increasing reliability and operational lifetime. The control logic provides power monitoring and an LED display for each supply in order to assist in status monitoring, rapid fault-isolation and network management.The 14-Module Powered Chassis supports any combination of FlexPoint media converter modules which are individually secured and hot-swappable to ensure continuous operation.The FlexPoint Powered Chassis is a rack-mount 14-Module, power-redundant chassis for media converter modulesDual hot-swappable power supplies ensure continuous network operationLED displays provide network management with continuous power supply status monitoringSupports any combination of protocol-independent media converter modules and mixed media; saves space and makes installation and support easySupports all FlexPoint media converter modulesConverters are individually secured and hot-swappable for maximum connection reliabilityStandard 19" rack-mount dimensions allow spacesaving and convenient installationAvailable in AC and DC modelsCompletely software independent with no installation of drivers requiredPeace-of-mind reliability backed by a lifetime warranty and free 24/7 technical support

The FlexPoint GX/T is a 10/100/1000BASE-T UTP to 1000BASE-X modular fiber media converter that supports jumbo frames up to 10,240 bytes. The GX/T features Small Form Pluggable (SFP) transceivers that support both 100BASE-FX and 1000BASE-X for interoperability with Gigabit and Fast Ethernet fiber equipment. SFP transceivers enable adaptability to different fiber types, speed and distances, and support Coarse Wave Division Multiplexing (CWDM) technology to increase the bandwidth capacity of fiber infrastructure.The FlexPoint GX/T also supports SC and ST fixed fiber connectors for multimode, single-mode fiber; and single-mode single-fiber models are available.Both the fiber port and the UTP port support auto-negotiation, an IEEE standard which defines how all the communicating devices automatically perform their configuration functions. Auto-negotiation achieves the best possible mode of operation (speed, duplex mode and Pause mode) between the devices.The FlexPoint GX/T is a 10/100/1000 copper to 100/1000* modular fiber media converterConforms to 10BASE-T, 100BASE-TX, 1000BASE-T, 100BASE-FX* and 1000BASE-X specificationsFiber port supports multimode and single-mode fiber with ST and SC connectors and single-fiber with SC connectorsSupports dual fiber and single-fiber 100BASE-FX or 1000BASE-X SFP transceivers for standard or CWDM wavelengthsBoth the fiber and UTP ports support auto-negotiationProvides Remote Fault Indicators to signal loss of link for Far-End Fault and Link Fault conditionsUTP port supports 10/100/1000Mbps and Half/Full-DuplexAuto or manually configured Pause function for flow controlSupports jumbo frames up to 10,240 bytesLoopback mode supports end-to-end testingUser-selectable Link Modes for quick fault detectionDiagnostic and DIP-switch configurations are displayed with status LEDs for quick and easy installationTabletop, wall-mounted, rack-mounted in a 5-Module shelf or in a 14-Module power-redundant chassis optionsLifetime Warranty and free 24/7 Technical Support

The FlexPoint 232 is a RS-232 to fiber media converter that provides reliable and cost-effective fiber extension for serial connections. The asynchronous RS-232 interface supports speeds up to 115,200 baud and supports RTS, CTS, DCD, DTR, and DSR hardware flow control signals providing plug and play connectivity with most serial devices. It features a switch for convenient connection to DTE or DCE equipment. The fiber port operates at 850nm or 1310nm and features ST, SC or LC connectors. Multimode fiber models support distances of up to 5km, and single-mode fiber models support distances of up to 60km. The FlexPoint 232 features descriptions of the LED indicators on the label for easy in-the-field installation and maintenance. The LEDs report the availability of power, DTE/DCE selection, fiber loopback status, port activity and link status. The FlexPoint 232 features remote loopback capability by testing the fiber link end-to-end from one physical location. FlexPoint modules can be mounted utilizing optional wall-mounting hardware or with DIN-rail mounting brackets. They can also be rack-mounted in a 5-Module shelf or in a high-density 14-Module, power-redundant Powered Chassis. FlexPoint modules installed in the 5-Module shelf or used as standalone devices can be powered by an external AC to DC power adapter, or through the 5VDC chassis connector. Standalone modules can also be powered by attaching an external DC power supply (18-60VDC). When used in the 14-Module power-redundant Powered Chassis with any combination of AC and DC power supplies, the installed modules are powered via the 5VDC chassis connector. The wide variety of FlexPoint mounting and power options provide flexible upgrade paths as network requirements change and grow. FlexPoint unmanaged media converters are easy to use and provide dependable fiber connectivity in Enterprise and Government networks around the world.

When individual mounting is required, the wall-mounting kit provides an easy and convenient way to secure a FlexPoint converter to a wall or a side of a desk. The mounting hardware is easy to use and flexible in different applications.

Omnitron's Small Form Pluggable (SFP) and 10 Gigabit SFP+/XFP optical transceivers are interchangeable, compact media connectors. They enable a single network device to connect to a wide variety of fiber and copper cable types and distances.Pluggable Optical Tranceivers are used to customize iConverter" , FlexPoint" , OmniConverter" and miConverter" products to meet specific networking protocols and media requirements. They support multimode dual fiber, single-mode dual fiber, single-mode single-fiber, Coarse Wave Division Multiplexing (see the CWDM Optical Transceiver Data Sheet) and Unshielded Twisted Pair copper cabling.

The iConverter Gx AN Media Converter is a manageable media converter that provides 1000BASE-T UTP to 1000BASE-X fiber conversion between Gigabit networking devices. The UTP port supports auto-negotiation or forced negotiation of duplex modes and pause capability while the fiber port supports both manual or auto-negotiation.SFP models support Small Form Pluggable (SFP) transceivers with Optical Statistics for standard or CWDM applicationsFixed-fiber connectors available for multimode and single-mode dual fiber and single-mode single-fiberUTP auto or forced negotitaion of duplex modes and pause capabilitiesFiber port supports auto or manual negotiationUser-selectable link fault detection modes facilitate quick fault detection, isolation and reportingManagement of the plug-in module is available with the addition of a management module to the chassisSNMP management via NetOutlook" provides module information, remote parameter configuration and trap notificationPlug-in modules are hot-swappable in 19-Module, 5-Module, 2-Module or 1-Module chassisLED displays for immediate visual status of each portLifetime Warranty and free 24/7 Technical Support

Omnitron's Small Form Pluggable (SFP) and 10 Gigabit SFP+/XFP optical transceivers are interchangeable, compact media connectors. They enable a single network device to connect to a wide variety of fiber and copper cable types and distances.Pluggable Optical Tranceivers are used to customize iConverter" , FlexPoint" , OmniConverter" and miConverter" products to meet specific networking protocols and media requirements. They support multimode dual fiber, single-mode dual fiber, single-mode single-fiber, Coarse Wave Division Multiplexing (see the CWDM Optical Transceiver Data Sheet) and Unshielded Twisted Pair copper cabling.

The 5-Module Chassis features two hot-swappable redundant power supplies. Universal AC power supplies can be used in any combination. Omnitron's redundant power supplies operate in load-sharing mode to reduce the burden on each power supply to extend the lifetime and fault tolerance.

The iConverter 8926N-0 Media Converter Interface Device conforms to the Ethernet in the First Mile (EFM) fiber standards to support Fiber-to-the-X Metropolitan and Enterprise LAN networks. conforms to the Ethernet in the First Mile (EFM) fiber standards to support Fiber-to-the-X Metropolitan and Enterprise LAN networks. iConverter 8926N-0 Media Converter Interface Device provides intelligent, securely managed service demarcation at the customer premises, offering Quality of Service and enhanced Bandwidth Control (rate-limiting) capabilities.

The iConverter NMM2 provides comprehensive remote monitoring, configuration and alarm notification functions for all iConverter managed media converters and Network Interface Devices (NIDs). Installed in any slot of an iConverter chassis, the NMM2 manages all other modules and power supplies installed in the chassis through a high-speed management backplane. Additionally, all remote NIDs linked to the managed iConverter chassis may be managed by the installed NMM2 through a secure IP-less management channel.

The FlexPoint T1/E1 is a modular T1/E1 copper-to-fiber media converter that provides reliable and cost-effective extension of devices such as PBXs, CSUs and routers via fiber.Designed as a transparent repeater, the FlexPoint T1/E1 supports standard T1, E1 and Primary Rate Interface (PRI), voice or data. The converter also supports AMI, B8ZS and HDB3 line codes. Manual switch settings with on-the-label descriptions enable easy configuration of T1/E1 line codes and line lengths.A crossover switch makes it simple to connect the FlexPoint T1/E1 converter to PBXs or CSUs and eliminates the need for crossover and custom cables to connect devices.The fiber port operates at 1310nm and supports SC or ST connectors. Multimode fiber models support distances of up to 5km, and single-mode fiber models support distances of up to 60km.The FlexPoint T1/E1 is a modular copper-to-fiber media converter that supports ANSI, AT&T, ITU and ETSI standardsSupports AMI, B8ZS and HDB3 line codesFiber port supports multimode or single-mode fiber SC or ST connectors, and distances up to 60kmLabeled status LEDs and switches for quick and easy installationFeatures a crossover switch for easy connections to PBXs or CSUsLocal and remote fiber loopback switches with optional all 1's insertion (AIS) to facilitate easy installationEquipped with dry relay contacts for connection to alarm equipmentWall-mount or rack-mount on a 5-Module shelf or in a 14-Module power-redundant FlexPoint Powered ChassisCompletely software independent with no installation of drivers requiredPeace-of-mind reliability backed by a lifetime warranty and free 24/7 technical support

The miConverter GX/T is a miniature 10/100/1000BASE-T UTP copper to 1000BASE-X fiber media converter that supports jumbo frames up to 10,240 bytes. The miConverter GX/T provides cost-effective fiber connectivity from Ethernet switches to diagnostic equipment, desktop and laptop computers.The GX/T features Small Form Pluggable (SFP) transceivers that support 1000BASE-X for interoperability with Gigabit fiber equipment. SFP transceivers enable adaptability to different fiber types, speed and distances, and support Coarse Wave Division Multiplexing (CWDM) technology to increase the bandwidth capacity of fiber infrastructure.The GX/T also supports SC and ST fixed fiber connectors for multimode, single-mode fiber; and single mode single-fiber models are available. Miniature Gigabit Ethernet media converter Supports 10/100/1000BASE-T, 1000BASE-X and the IEEE 802.3 specification Plug-and-Play capability USB power via optional Power Adapter Cable Supports Full/Half-Duplex fiber optic auto-negotiation Multimode and single-mode fiber options LED indicators for UTP and fiber status Domestic, Universal and Country/Region specific power supply options Wall-mount with optional mounting brackets or included Velcro® strips Small and lightweight, only 5 ounces (without power supply) Cost-effective Lifetime Warranty and free 24/7 Technical Support

The miConverter GX/T is a miniature 10/100/1000BASE-T UTP copper to 1000BASE-X fiber media converter that supports jumbo frames up to 10,240 bytes. The miConverter GX/T provides cost-effective fiber connectivity from Ethernet switches to diagnostic equipment, desktop and laptop computers.The GX/T also supports multimode, single-mode fiber; and single mode single-fiber models are available.The GX/T features SC and ST fixed fiber connectors, or Small Form Pluggable (SFP) transceivers.Supports 1000BASE-T, 1000BASE-X and the IEEE 802.3 specificationPlug-and-Play capabilityUSB power via optional Power Adapter CableSupports Full/Half-Duplex fiber optic auto-negotiationMultimode and single-mode fiber optionsLED indicators for UTP and fiber statusDomestic, Universal and Country/Region specific power supply optionsWall-mount with optional mounting brackets or an 18-Module Powered ChassisSmall and lightweight, only 5 ounces (without power supply)Cost-effectiveCommercial (0 to 50ºC), wide (-40º to 60ºC), extended (-40º to 75º C) and industrial (-40º to 85ºC) temperature rangesLifetime Warranty and free 24/7 Technical Support

The miniature miConverter 10/100 and miConverter 10/100 Plus are rate-switching 10/100 UTP copper to 100BASE-FX fiber media converters. The miConverter provides cost-effective fiber connectivity from Ethernet switches to diagnostic equipment, desktop and laptop computers.They can be powered by a computer's USB port using the optional USB Power Adaptor Cable, which reduces the module's weight and eliminates the need to tether the miConverter to an electrical outlet that provide cost-effective fiber network extension and connectivity.Miniature 10/100BASE-TX to 100BASE-FX Ethernet media converterSupports 10BASE-T, 100BASE-TX, 100BASE-FX and the IEEE 802.3 specificationSupports Full/Half-Duplex UTP auto-negotiationAutomatically detects and adjusts crossover functionMultimode, single-mode and single-fiber optionsST or SC fiber connector optionsDomestic, Universal and Country/Region specific AC power supply options availableOptional USB power adapter cable available for operation without AC power adapterThe miConverter 10/100 Plus features DIP-switches for UTP and Link Mode configurationsLED indicators for UTP and fiber statusWall-mount with optional mounting bracketsCost-effectiveSmall and light, weighs only 5 ounces (without power supply)Lifetime Warranty and free 24/7 Technical Support

The miConverter 18-Module Power Chassis is a cost- effective mounting and powering solution for miConverter miniature media converters. This compact chassis is ideal for consolidating multiple media converters into a high- density, rack mountable form factor. It can be deployed in Service Provider, Enterprise and Government applications where fber optic links are distributed from UTP switch equipment. The miConverter chassis is suitable for Fiber- to-the-Desk, Campus LAN/WAN fber networks and hybrid copper/fber networks.

The OmniConverter GPoE+/M is a compact managed PoE and PoE+ Ethernet fiber switch that features one or two Gigabit fiber ports and four or eight 10/100/1000 RJ-45 copper Power Sourcing Power-over-Ethernet ports. The GPoE+/M enables network distance extension with fiber cabling and provides PoE+ power to all RJ-45 ports. The OmniConverter GPoE+/M is a standard Layer 2 Ethernet switch that forwards frames to any port based on their MAC address. The OmniConverter GPoE+/M supports Directed Switch mode, which directs multicast traffic (such as video) only to the appropriate fiber port, preventing the multicast video traffic from flooding other network ports. Models with two fiber ports support redundant fiber uplinks for critical applications that require protection and sub 50ms restoration in the event of a fiber failure. The second fiber port may also be used to daisy-chain multiple Ethernet switches, or it may be used as another switch port. Models with two fiber ports also support Dual Device mode that enables the GPoE+/M to operate as two independent and isolated Ethernet switches. In Dual Device mode, the GPoE+/M provides separate and independent data traffic paths between the two fiber links and four or eight RJ-45 ports. The GPoE+/M modes of operation can be configured using easily accessible DIP-switches or using Web, Telnet, SSH or Serial Console management interfaces. The GPoE+/M supports in-band and out-of-band management. In-band management is provided by accessing the module through any of the Ethernet RJ-45 or fiber ports and supports IP-based web, Telnet, SSH and SNMPv1/v2c management interfaces. Out-of-band management is provided by accessing the serial console port. Omnitron's NetOutlook SMNP software can be used for real-time alarm reporting and monitoring of each port. The OmniConverter GPoE+/M is available with fixed ST, SC, and LC connectors or Small Form Pluggable (SFP) transceiver receptacles. Fiber ports support multimode or single-mode and dual fiber or single-fiber with distances up to 140 km. SFPs support a variety of distances in standard and CWDM wavelengths. The GPoE+/M automatically negotiates and delivers the power level required by its Powered Device (PD) partner. When negotiating to PoE (IEEE 802.3af) it delivers up to 15.4 Watts per RJ-45 port. When negotiating to PoE+ (IEEE 802.3at) it delivers up to 30 Watts per RJ-45 port. The GPoE+/M features a remote PoE power reset function that can be configured with a DIP-switch or via management. The PoE power reset feature allows all PDs or individual PDs to be power-cycled and reset remotely to save time and expense by eliminating the need to dispatch manpower to remote network sites. The GPoE+/M also features a heartbeat signal that when configured will periodically ping the attached PD. On a loss of connectivity to the PD, the GPoE+/M can automatically power cycle or shutdown the PD. The OmniConverter compact PoE fiber switches can be wall mounted or DIN-rail mounted using an optional mounting clip. They are available with 2- Pin DC Terminal and AC to DC 100 - 240VAC power adapters.